works

done (gpg4win -Beta41)

Looks good, gpg4win-Beta41:

Done, checked with Gpg4win-Beta41

Texts are improved, checked with Gpg4win Beta-41

ok, checked with Beta-41

noticed testing T7128: The Token is very long. Is the serial number not unique? That one is much shorter and therefore better to handle visually

tested with Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41)

Checked in Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41):
Looks ok to me.

This is how the upper part of the "New Group" window looks with Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41):

The basic task is definitively done and looks good.
It is not clear if the improvement wishes commented later have consensus and they should be addressed in an new ticket, anyway.

Tested with Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41)

With Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41) I see the expected result. The width for the additional columns is as expected too. So I'll mark this task as done.

Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41):
works as described with pkcs#15 and netkey cards.
(The column width is then the same for those cards)

ok, here the comments from our joined feedback session:

The order of states is "expired", "revoked", "disabled", "invalid", "certified", "not certified". Since we show only one state we need to define an order. I guess it would make sense to give "disabled" the highest priority. (I also think that "revoked" should have higher priority than "expired".)

This is how it looked before (VSD 3.2.2):

Well, now it does not occur for me any more, either. Ok, I'm setting this to resolved, this was most likely a situation where Kleopatra could not write to the kleopatrastaterc (in %APPDATA%\kleopatra\) for some reason. This would then be a more general issue, anyhow, for which we need another ticket if we can reproduce this.

with Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41):

I did what you did, didn't even need to restart Kleopatra.

With Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41) II can add a keygrip column to the subkey details. But if I close the details window and open it again, the column are no longer selected.

You could use colors, fonts, icons to mark any certificate you want instead of having to use tags and filter by them. You could even put their company logo on certificates of your communication partners.

As it was a fresh install of a gpg4win test version I used: yes, common.conf was not only supposed to be there, it is and keyboxd.exe is shown in the task manager.
But I think it not only needs to be solved for keyboxd, as our VSD customers don't have that.

From the support angle, the worst of these issues is that the default will not be restored for VS-NfD. But then: nobody has inquired about that yet…

ok, works with Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41).

works now, Version 3.2.2.2405000+git~ (Gpg4win-4.3.2-beta41)

As for renaming "Change Reset Code" to "Set Reset Code", what about "Change PIN" and "Change Admin PIN"? Should they also be renamed? If not, why not? Is there no default reset code? Is there a way to find out whether the reset code has already been set (in which case "change" would be more appropriate than "set")?